Our Products
KEENE IR DISTRIBUTION AMP KIT (INC IRPMR)
Brand: Keene Electronics
[IRBKITPB] £ 65.00 (£ 55.32 ex VAT)
Add to order


Put your remote back in control and route IR commands to wherever they are needed even round corners and inside cabinets. Multiple input/output options (see components list below for more details) can provide a solution to almost any IR control problem.

This is a complete kit, comprising the Keene IR Distribution Amplifier, 240V UK mains power adaptor, 2 x universal emitter wands (see output component [IRUW] below), 1 x Panel Mount IR receiver (IRPMR black) and instruction leaflet.

ALL Keene IR Distribution systems are designed to filter and reject unwanted interference from Plasma & LCD screens to give you dependable, reliable results every single time.



Also available with IRPMR receiver in white.
IRBKITPW

Also available without an IR receiver.
IRBKIT

Also available as complete kit including a standard receiver.
IRBKITS

INPUT COMPONENTS

Standard IR Receiver 40kHz suitable for most domestic equipment.
IRSR

Wide Band IR Receiver Up to 100kHz for more esoteric equipment.
IRWBR

Standard IR Receiver wall plate. 40kHz suitable for most domestic equipment, built into a single gang faceplate
IRSP

Wideband IR Receiver wall plate. 100kHz suitable for most esoteric equipment, built into a single gang faceplate
IRSPW

Standard IR Receiver Panel Mount. 40kHz suitable for most domestic equipment, requires 16mm diameter hole. (Black)
IRPMR

Standard IR Receiver Panel Mount. 40kHz suitable for most domestic equipment, requires 16mm diameter hole. (White)
IRPMRW

Standard IR Receiver Panel Mount. 40kHz suitable for most domestic equipment, requires 16mm diameter hole.(brass)
IRPMRB

Standard IR Receiver Panel Mount. 40kHz suitable for most domestic equipment, requires 16mm diameter hole.(chrome)
IPRMC

Powermid IR lead To feed a Powermid RF receiver output directly to the IR Distribution Amp input (3.5mm stereo jack plug to 3.5mm stereo jack plug 1.5m long). KLDE6M

Wavecom IR lead To feed a Wavecom RF receiver output directly to the IR Distribution Amp input (2.5mm stereo jack plug to 3.5mm stereo jack plug 1.5m long). KLDE10

Input splitter 1 x 3.5mm stereo jack plug to 2 x 3.5mm stereo jack sockets adaptor. Allows the IR Distribution Amp input to be fed by both a cabled feed (from say a Powermid RF receiver) and an in-room
IR receiver. KA109


OUTPUT COMPONENTS

Universal Wand. IR Universal Wand. Can only be used in low power outputs. The emitter allows for equipment fascia or shelf mounting.
IRUW

Low Power Wand. Can be attached directly to the equipment facia or will work up to 4 metres away. Even when attached directly the equipment will still respond to external IR signals. Only to be used with Keene IR systems.
IRLPW

High Power Wand. Will operate equipment from up to 10 meters away. Can also be used in the IR Distribution Amp low power output sockets if required, but will then only perform as a low power emitter. Not suitable for one-to-one operation.
IRHPW

Side Firing Wand. A short range emitter for direct attachment to the equipment fascia.
IRSFW

Dual Blinking Wands. The single jack plug drives two IR emitter wands. The emitters are extremely tiny (just 9mm across) and are supplied with double sided adhesive pads to affix directly to the equipment fascia. The emitters actually flash red as IR signal is emitted giving visual confirmation that the IR signal was received and transmitted correctly.
IRDW


EXTENSION

Extension leads, 3.5mm stereo jack plug to 3.5mm stereo socket to be used on input or output as required. We've tested the input up to 10m and the output to 20m.
3m extension KLD40
5m extension KLD405
10m extension KLD4010

You can extend the input much further by using CAT5 cable and a pair of these KA175

Have a look at the instruction sheet here (Acrobat pdf file)

KEENE IR DISTRIBUTION AMP KIT (INC STD RECEIVER)

please click to see larger image [IRBKITS] £ 48.00
(£ 40.85 ex VAT)
Put your remote back in control and rout more info
Add to order

KEENE IR DISTRIBUTION AMP KIT (INC IRPMRW)

please click to see larger image [IRBKITPW] £ 65.00
(£ 55.32 ex VAT)
Put your remote back in control and rout more info
Add to order

KEENE IR COMMANDER MATRIX

please click to see larger image [IRCM] £ 169.99
(£ 144.67 ex VAT)
IR Commander Matrix IRCM
This is the more info
Add to order
there are no customer reviews at present
want to be the first to offer a review?
to place a review click here

Ask a Question?

If you would like to ask us a question about this product, please feel free to click here to Ask a Question


Previous Questions

1 MARK on 06 Jan 2010 asked  :
" How long is the IRPMR receiver and IRUW wand thanks "

Keene replied: The receiver is 1.5m the wand 1.2m approx.


If you feel something is not correct with this product please contact us using the same link

Tell a friend?

Want to tell a friend about this page?

Tell a friend

please click to see larger image
Mega Deal
REFLECTA 100W 12V VIDEO LIGHT KIT
please click to see larger image [DR100] £ 119.99
(£ 102.12 ex VAT)
Brand: Reflecta
Bookmark and Share
Keene electronics catalogue
Keene HDMI catalogue
Would you like to sign up for our newsletter?
*  Your email address:
*  Enter the security code shown: