Put your remote back in control and route IR commands to wherever they are needed even round corners and inside cabinets. Multiple input/output options (see components list below for more details) can provide a solution to almost any IR control problem.

This is a complete kit, comprising the Keene IR Distribution Amplifier, 240V UK mains power adaptor, 2 x universal emitter wands (see output component [IRUW] below), 1 x Panel Mount IR receiver (IRPMR white) and instruction leaflet.

ALL Keene IR Distribution systems are designed to filter and reject unwanted interference from Plasma & LCD screens to give you dependable, reliable results every single time.



Also available with an IRPMR receiver in black.
IRBKITPB

Also available without an IR receiver.
IRBKIT

Also available as complete kit including a standard receiver.
IRBKITS

INPUT COMPONENTS

Standard IR Receiver 40kHz suitable for most domestic equipment.
IRSR

Wide Band IR Receiver Up to 100kHz for more esoteric equipment.
IRWBR

Fascia Mount Semi-Wideband IR Receiver 30-60KHz.
IRFMR

Standard IR Receiver wall plate. 40kHz suitable for most domestic equipment, built into a single gang faceplate
IRSP

Wideband IR Receiver wall plate. 100kHz suitable for most esoteric equipment, built into a single gang faceplate
IRSPW

Standard IR Receiver Panel Mount. 40kHz suitable for most domestic equipment, requires 16mm diameter hole (black)
IRPMR

Standard IR Receiver Panel Mount. 40kHz suitable for most domestic equipment, requires 16mm diameter hole (brass)
IRPMRB

Standard IR Receiver Panel Mount. 40kHz suitable for most domestic equipment, requires 16mm diameter hole (chrome)
IRPMRC


Powermid IR lead To feed a Powermid RF receiver output directly to the IR Distribution Amp input (3.5mm stereo jack plug to 3.5mm stereo jack plug 1.5m long). KLDE6M

Wavecom IR lead To feed a Wavecom RF receiver output directly to the IR Distribution Amp input (2.5mm stereo jack plug to 3.5mm stereo jack plug 1.5m long). KLDE10

Input splitter 1 x 3.5mm stereo jack plug to 3 x 3.5mm stereo jack sockets adaptor. Allows the IR Distribution Amp input to be fed by up to three IR receivers.
KA203


OUTPUT COMPONENTS

Universal Wand. IR Universal Wand. Can only be used in low power outputs. The emitter allows for equipment fascia or shelf mounting.
IRUW

Low Power Wand. Can be attached directly to the equipment facia or will work up to 4 metres away. Even when attached directly the equipment will still respond to external IR signals. Only to be used with Keene IR systems.
IRLPW

High Power Wand. Will operate equipment from up to 10 meters away. Can also be used in the IR Distribution Amp low power output sockets if required, but will then only perform as a low power emitter. Not suitable for one-to-one operation.
IRHPW

Side Firing Wand. A short range emitter for direct attachment to the equipment fascia.
IRSFW

Dual Blinking Wands. The single jack plug drives two IR emitter wands. The emitters are extremely tiny (just 9mm across) and are supplied with double sided adhesive pads to affix directly to the equipment fascia. The emitters actually flash red as IR signal is emitted giving visual confirmation that the IR signal was received and transmitted correctly.
IRDW


EXTENSION

Extension leads, 3.5mm stereo jack plug to 3.5mm stereo socket to be used on input or output as required. We've tested the input up to 10m and the output to 20m.
3m extension KLD40
5m extension KLD405
10m extension KLD4010

You can extend the input much further by using CAT5 cable and a pair of these KA175

Have a look at the instruction sheet here (Acrobat pdf file)

You can also view the IR receivers and Emitter connection diagrams here (Acrobat pdf file)