Keene Bluetooth In Wall Digital Amplifier Including Power Supply (grey)

Keene Bluetooth In Wall Digital Amplifier Including Power Supply (grey)

Bluetooth Receiver Wallplate and Backbox

Bluetooth Receiver Wallplate and Backbox

Keene KLABXB 20w Bluetooth Express In Wall Amplifier Kit Including Power Supply

£119.99 £99.99
Availability: In stock
Product Code
KLABXB
KLABXB Bluetooth Express Digital In-wall Stereo Amplifier

Easily add music to your kitchen, bedroom, study, bathroom etc. This tiny wall mount amplifier fits into a standard UK two gang pattress and provides a powerful 20W RMS per channel. In operation it really couldn't be any easier. When you want to use it simply connect via Bluetooth and control the volume with your bluetooth device. When you disconnect or stop streaming the amplifier automatically switches into very low power standby mode. Whenever you connect again it instantly wakes up to deliver clear powerful audio.

There are no switches or remote controls, it really is a fit and forget solution. During installation you can choose from one of seven Bluetooth ID's to make sure you are always connecting to the correct amplifier. Its also easy to use with an Amazon Echo Dot. (Acrobat pdf file)


Features
Up to 20W RMS per channel
Low distortion Digital Class D design means high efficiency with minimal heat produced
Fully Automatic fit and forget design
Ultra low current draw in standby (less than 20mA = 0.3W @15vDC)
Supports Bluetooth SSP for quick pairing.
Supports A2DP Codecs: SBC, MPEG1,2 audio / mpeg2,4 AAC /ATRAC /APTX
LED's for status and confirmation
Flush mount or surface mount (25mm depth, or 35mm for dry-lining)
Detachable speaker connectors for easy install.

Whats in the box?
KLABXB Amplifier
Power Supply Input: 100-240v AC Output: 60W DC
Screwdriver
Fixing screws
Instruction sheet

Specifications:
Bluetooth Audio Modes: A2DP Codecs: SBC, MPEG1,2 audio / mpeg2,4 AAC /ATRAC /APTX
Power output (15v supply): 20W RMS per channel into 4ohms
Power output (12v supply): 18W RMS per channel into 4ohms
Total Harmonic Distortion + Noise: 0.15% (4ohm load, 1KHz, 8W power)
Bandwidth: 20Hz to 22KHz Passive limitation built in
Power Supply: 12V to 18V (absolute max 18V DC) minimum current 3.0A. Connection via a 2.1mm DC connector centre positive, auto mute on under voltage.
Fuse: self resetting 3A built in to clear remove power for at least 20 seconds, clear fault and reconnect
Amplifier topology: full bridge mode all speaker connections are live ( no common ground connection)
Recommended min speaker impedance:4 ohms per channel
Absolute minimum speaker impedance: 3 ohms per channel
SNR: 98dB
Voltage gain: 33dB
Input required to produce full output: approx 775mV
Standby current: 20mA (0.3W at 15v supply)
Loudpeaker wire size: solid min 0.14mm2 max 2.5mm2, stranded min 0.14mm2 max 1.5mm2



Special Offer!
Also available as a money saving deal combining the KLABXB Bluetooth In-wall Amplifier and power supply with a pair of 5" 60W Moisture resistant Loudspeakers! KLABXBDEAL

Helpful codes
KBL31 Speaker cable.
MPATLD Flush mount metal pattress, 25mm deep.
MPAT35D Flush mount metal pattress, 35mm deep.
PAT3D Surface mount white plastic pattress, 30mm deep.

More Information
Info High power bluetooth amplifer that takes up no more room than a twin plug socket
Fit and forget - automatically switches to low power standby when not in use
Easy pairing with any bluetooth device
Supports A2DP Codecs: SBC, MPEG1,2 audio / mpeg2,4 AAC /ATRAC /APTX
Write Your Own Review
Only registered users can write reviews. Please Sign in or create an account